Home > Commercial > Vinyl Plank  > Vinyl plank

Vinyl plank - Super Plank $35.5 Sqm Antique 1955
Search :  
Advanced Search
Sale Price
Was : $
48.50 M2
Now : $
41.50 M2
Product Only
Installation Available Now !
Antique 1955
Coromandel 1960
Ghost Gum 1953
Golden Birch 1930
Honey Oak 1932
Jarrah 1959
Marri 1954
Oak 1237
Red Oak
Rimu 1928
Silverwood 1950
Victorian Ash 1961
Walnut 1957
Wandoo 1962

1. GENERAL INFORMATION

Well planned and regular maintenance, tailored to

traffic

conditions and frequencies, will help keep the

floorcovering

in pristine condition. Without regular maintenance, standards

of appearance, hygiene and cleanliness, as well as the life

expectancy of the floorcovering, will be compromised.

EXPONA incorporates a polyurethane (PU) surface treatment,

which protects the

protection facilitates the maintenance and

foundation for the ongoing maintenance regime.

floorcoverings by resisting soiling. Thisprovides the

2. PREVENTATIVE MEASURES

In the initial stages of construction planning, attention should

be

enter the

installation of

e.g. scraper and moisture mats. The mats should

to ensure that access cannot

paid to minimising the amount of dirt and water that canbuilding. To facilitate this we strongly recommend thepassive dirt barrier systems in all entrance areasbe positionedbe gained without walking on

them, ideally they should be at least four to six paces wide.

3. INITIAL CONSTRUCTION CLEAN

After laying, a

contamination and residue caused

final construction cleaning is to be carried out. Allby production is completely

removed

here with a neutral or PU cleaner. The surface can be

polished if desired with a single-disc machine (at least 400–600

rpm.) through using a white polishing pad, or in the case of

strongly structured surfaces, by means of soft brush.

4. APPLICATION OF A FLOORDRESSING

The initial treatment is not necessary in the case of

coverings with a PU laye

The factory PU surface coating makes a simple,

and economic cleaning possible.

floorr.advantageous

5. ROUTINE MAINTENANCE

Daily

Mop sweep or

vacuum the floor to remove dust and loose dirt.

Stubborn

cleanser. If required, dry

a white pad.

marks should be removed using a neutral or a PUbuff with a single-disc machine and

Damp mop

Thanks to a 2-step mopping system with

double wheeled

bucket, good cleaning results are obtained.

Spray Cleaning / Burnishing

Burnish the

rpm) and clean the

product. This will add further protection and it will

floor by using a rotary machine (at least 400–600floor by additionally using a spray cleaningimprove the

appearance of the floorcovering. Use a clean soft white pad.

6. PERIODICALLY

It may

to time

manufacturers’ instructions.

become necessary to remove stubborn marks from timeby using a neutral or a PU detergent according to the

7. REMOVAL OF POLISH

From time to time it will

layers, e.g. when routine maintenance does no longer

about

on

any unsightly

applying an emulsion polish stripper. The

be necessary to strip back the polishbringa satisfactory result. The interval is very much dependanttraffic conditions and maintenance methods. All soiling andbuild up of polish should be removed by initiallyfloor should then

be scrubbed

or a

Neutralise the

using a mono-pad rotary machine (green pad)scrubber and the slurry should be removed completely.floor with clean water. Then re-apply a floor

dressing (polish of the polymer dispersion type or of the PU

sealing type).

Please heed the recommendations of the cleaning agent

manufacturer

IMPORTANT NOTES

For hairdresser salons, car dealers

Substances

removed

with a colouring or bleaching effect must beimmediately from the covering, in order to avoid

any lasting impairment to the appearance. In these areas

an additional coating with a mark-resistant 2-component PU

sealing product is

absolutely necessary even in the case of

coverings which already have a PU laye

r.

For the health service

In areas where palm and skin disinfectants are used, we

recommend an additional treatment with

suitable polymer

dispersion or PU sealing product before the first use.

For strongly frequented areas and surfaces

In areas which are expected to

shops, entrances, receptions etc., we recommend applying a

be highly frequented, e.g.

suitable PU sealing product before first use.

General information

When using wheeled chairs,

double swivel rollers are to be

used (soft type). The contact areas of

mobile furniture should

be equipped with suitable felt or soft plastic bearings.

When selecting cleaning and maintenance products and the

mechanics used, ensure that these are adapted to one another

and consider the manufacturer’s notes.

09 / 2010